Schematic diagram of the plate-load test setup: Foundation design — principles and practices. The journal reviewers are thanked for their constructive comments that helped sharpen this paper. Figures 5 and 6 show schematic diagrams of the setup of the plate-load test, Fig. The modulus KS decreases as the size of the plate increases. To accommodate larger size plates, it was decided to use eight reaction anchors, each carrying an allowable load of up to aatm t.
The results of these plate-load tests are presented in this paper. The field portion of the study included a test pit exploration and plate-load tests. The test site is located in the City of Taichung, Taiwan, which is in the Taichung Basin, a concave Neotectonic basin located in midwest Taiwan.
Nevertheless, the tests were conducted from small plate to large plate, with a aztm day time interval between the tests, to minimize the effect. This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.
We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience.
Necessary cookies are absolutely essential for the website to function properly. Apply the load to the soil in increments corresponding to settlement increments of approximately 0. Your email address will astm d be published. Individual reprints single or multiple astm d of this standard may be obtained by contacting ASTM at the above address or at phone. Thu Jul 2 A standard may be withdrawn with or without replacement.
The Static Plate Load Test can be utilized in earthworks and foundation astm d, as well as road construction in order to determine load settlement lines and by this astm d d evaluate the deformability and the load capacity of the soil. Your email address will not be published. The two active ones are for pavement design, astm d you astm d gain the same type of info. D — 94 FIG. NOTE 2—For footings placed under permanently astm d basements the depth of the actual footing is construed as the depth from the basement level astm d astm d over which the surcharge is permanently acting, rather than the depth astm d the ground surface.
By joining you are opting astm d to receive e-mail. But in Europe an alternative method is used instead of it, the method of screw plates test which was developed in Europe and is now implemented there.
Astm d typical assembly for conducting astm d d tests is illustrated in Fig. Click Here to join Eng-Tips and talk with other astm d Unless otherwise specified, make the load astm d at the elevation of r proposed footings and under the same conditions to which the proposed footings will be subjected. Your comments will astm d careful astm d at a meeting of the responsible technical committee. Subsequent to the last load step the relief and a second loading similar to the first loading takes place.
Miscellaneous Apparatus required, including loading columns, steel shims, and other construction tools and equipment required for preparation of the test pits and loading apparatus. In rock, plates larger than mm diameter may be used, depending on the jointing frequency. In addition to the continuous listing of all time, load, and settlement data for each test, the report shall include at least the followings:. Click Here to join Eng-Tips and talk with other members! The Hydraulic or Mechanical Jack Assembly should have sufficient capacity to provide and maintain the aztm estimated load but not less than 50 tons in any case.
For bearing plates, three circular steel bearing plates, not less than 25mm in thickness and varying in diameter from mm to mm including the minimum and maximum diameter specified or square steel bearing plates of equivalent area. Thank you for helping keep Eng-Tips Forums free from inappropriate posts. The plate load test shall be carried out at locations as shown in the drawings or as directed by the Engineer using approved equipment.
The plate bearing load test shall be discontinued if any of the following occurs: Download Now Defense manufacturing is all about project manufacturing and project accounting.
Digital Transformation may be defined in a number of different ways by analysts or enterprise software vendors. The two active ones are for pavement design, but you can gain the same type of info. This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.
We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent.
0コメント